This essay Plastics Engineering has a total of 568 words and 6 pages.
Most people have never heard of injection
molding, however the products
that are produced through this process
are as common as a toothbrush, a compact
disk, or even drinking glasses.
Injection Molding is one of the
principal processes used in converting
plastics into useful products. An
injection molding machine can be large or small
but work through the same general process.
The machine heats a thermoplastic
material that in its pre-processing state
is pelletized or granular, to a liquid-like"flowable" state. It then injects the
melted plastic into a mold that is used to create
the desired shape of the product. The
plastic in the mold is then allowed to cool
and removed form the mold by an ejector
Different raw plastics materials can be
used in the injection molding
process. Most commonly injection molding
machines provide processing for
phenolics, melamine, silicone, elastomers
and polyester. These materials can be
numerous colors and can be used for making
the various products depending on
what characteristics like elasticity.
flexibility and hardness are needed.
The injection molding machine has two main
components the injection unit
and the clamp unit. The injection
unit melts and injects the materials. There are
usually about eight main parts that make
up the injection unit, and they are the
barrel, the nozzle, the screw and non
return valve, heater bands, a motor to rotate
the screw, and a hydraulic cylinder to
move the screw forward and backward.
Control systems are used for temperature
regulation, and the timing of the screw
rotation and injection strokes.
The screw consits of three main sections
the metering zone, the transition
zone and the feed zone. The feed
zone makes up about 1/2 the total length of the
screw. It has deep flights and is where
the pellets first enter the screw. The
transition zone is about 1/4 the length
of the screw and has flights that are closer
together to compress the pellets and aid
in the melting process. The metering zone
makes up the last portion of the screw
mechanism and is where any final melting
of the pellets occurs before the pellets
pass through the non return valve and
nozzle into the mold.
The Clamping unit opens and closes the
mold and ejects the parts. The two
most common methods to generate clamping
forces are direct hydraulic clamps
and toggle clamps that are both actuated
by hydraulic cylinders. In addition to
those parts most injection molding machines
also have a hydraulic pump and
Safety is a very important aspect of injection
molding so most injection
molding machines are equipped with safety
devices. These devices can be mold
closing safety systems, purge guards,
and rear door systems. Mold closing
systems are required to have a mechanical
drop bar, electrical interlocks and
hydraulic interlocks which all help protect
the operator from injury.
The actual injection molding process consists
of 5 basic steps:
1. The mold closes.
2. The screw moves forward and forces
the melted material into the mold
3. the screw maintains pressure through
the nozzle while the plastic is
4. The timers stop injection pressure
and the screw turns to draw fresh
5. The mold opens and ejector pins remove
the molded part.
All these steps can also be grouped in
a time cycle being: fill time, pack
time, cooling time, and dead time.
There are advantages and there are disadvantages
to injection molding.
Some of the advantages are that the surface
finish can be controlled to make any
texture, metal inserts can be used to
make things like screwdrivers, and with
thermo plastics the waste material can
be ground and used again. There are also
disadvantages like the high cost of the
molds and that the molds are to expensive
for just short product runs.
Through advances in injection molding plastics
are becoming more popular
and are being used to produce a wider
variety of products.
BP AmocoBP Amoco BP Amoco British Petrochemical Corporation registered on April 14, 1909, as the Anglo-Persian Oil Company, Ltd. It was named the Anglo-Iranian Oil Company, Ltd., in 1935 and changed its name to the British Petroleum Company Limited in 1954. The current name was adopted in 1982. The company’s headquarters are in London. The Anglo-Persian Oil Company was formed in 1909 to take over and finance an oil-field concession granted in 1901 by the Iranian government to an English investor, Willia
MexicoMexico Mexico Country Profile Country Formal Name: United Mexican States (Estados Unidos Mexicans). Short Form: Mexico. Term for Citizen(s): Mexican(s). Capital: Mexico City (called Mééxico or Ciudad de Mééxico in country). Date of Independence: September 16, 1810 (from Spain). National Holidays: May 5, commemorating the victory over the French at the Battle of Puebla; September 16, Independence Day. Mexico Geography Size: 1,972,550 square kilometers--third largest nation in Latin America (after
Manufacture In Scotland TodayManufacture In Scotland Today Manufacture In Scotland Today Contents Contents page Page 1 Introduction Page 2 Electronics Page 3 Semiconductors Page 5 Aerospace Page 6 Automotive Page 7 Conclusion Page 8 References Page 9 Manufacturing In Scotland Today Introduction This report is not so much on the state of the manufacturing industry in Scotland but rather of it’s current success. Scottish productivity consistently ranks among the highest worldwide and multinational companies have expanded th